| Environment temperature |
-40c- + 80c |
| Atmospheric pressure |
86-106 KPa |
| Relative Humidity |
10% -95% |
| Environmental noise |
<= 60dB (A) |
| Alarm sound level |
=30dB (A) |
| Working voltage |
11V~16Vdc(12Vdc/400mA) |
| Product Weight |
58 g |
| Product size |
Diameter 73 mm x thickness 23 mm |
? Display Information:vehicle
speed, engine RPM, water temperature, voltage, instantaneous fuel
consumption, average fuel consumption, single driving distance,total
driving distance, driving time,turbo pressure, Air/Fuel Ratio, oil temperature
? Alarm: low voltage alarm,high water temperature alarm,over speed alarm, engine fault code alarm, eliminate the fault code,freely switch between kilometers&miles ( km/h & MPH), Celsius and Fahrenheit (¡ãC & ¨H ) switch freely…
? Add new functions: accelerating competitive mode ,Brake performance test, can read the entire car data stream information
Wide Compatibility: available for cars with OBD2 and EUOBD port, plug and play;
Attention:
The OBD2 mode are not compatible with following cars:
– European and American cars manufactured before 2008 and Asian cars manufactured before 2008.
– American cars produced before 2008 and all Dodge, JEEP, Sail, Chrysler cars.
– France cars manufactured by FAT,DS,PEUGEOT,Citroen,Renault,Simka, Amirka
–
Japanese cars: Suzuki, Mazda, Infiniti (QX50, Q50, Q501), Toyota
avanza 2013, Lexus (is250, ex250, ES300H), Honda (jazz, CRV) are not
compatible. And all Japanese cars before 2008 are not compatiable.
– Some models of Kia and Hyundai cannot use this OBD2 HUD (2013 Hyundai Sonata, 2017 Kia Soul PS, etc.)
– Oil-electric hybrid and some diesel vehicles cannot use OBD2 HUD, GPS HUD are recommended.
– Pickup Trucks and Modified ECU vehicles are not suitable for this HUD.
If you are not sure this product is suitable for your car or not, please contact us before ordering, thank you!
Package List:
1 * Velcro sticker
1.The screen without any display,and no electricity
Start
the car engine;check if the OBD cable line is tight;please pull
down the OBD cable several times to confirm;check if HUD power switch
turns on. If no display still,please test the device on a different car,
analyze whether the car OBD diagnostic interface is good, if it is not
good,please repair it and try again.
2.When HUD power on, HUD only shows the car voltage and be automatic power off after 30 seconds driving.
HUD
is only suitable for cars with OBD2 agreement and EU-OBD
agreement£¨European region: after 03 years, Other region:after 07 years£©
HUD Products donnot support JOBD and OBDI and recommended test for another car.
3.See not clearly when HUD under the sunlight,and with double reflection.
Check
whether the HUD host surface protective film is torn,and please
stick the reflection film on the windscreen.And vertical press in the
setting button for 5 seconds to enter into menu setting when HUD is
power on,short press 2 times to menu 2,adjust the parameter to
5,vertical press in 5 seconds to save.
4.Inaccurate Speed
a.First
check the speed unit is correct or not, the speed unit can switch into
KM/H and MPH, short press in the wave button to switch between KM/H and
MPH
b.When
HUD is power on,vertical press the setting button for 5 seconds to
enter into the menu options, find menu 1,the parameter shows 107,up
or down the setting button to increase or decrease the value according
to the difference until it shows correct one.After adjustment, vertical
press in 5 seconds to save it.
5.Wrong operation lead to crashes. Or inaccurate datas
Do a reset setting.
Reviews
There are no reviews yet.